MIL-STD-461G CS109'a göre EUT, bireysel ekipman veya alt sistem spesifikasyonunda belirtilen toleransların ötesinde herhangi bir arıza, performans düşüşü veya belirtilen göstergelerden sapma göstermemelidir.
Test ekipmanı aşağıdaki gibi olacaktır:
- sinyal üreteci
- Amplifikatör (gerekirse)
- İzolasyon transformatörleri
- Akım probu
- Ölçüm alıcısı
- Direnç, 0,5 ohm
- kaplin trafosu
Test prosedürleri aşağıdaki gibi olacaktır:
A. EUT'yi ve ölçüm ekipmanını açın ve stabilizasyon için yeterli zaman tanıyın.
B. Sinyal üretecini gereken en düşük frekansa ayarlayın. Sinyal üretecini minimum olarak gerekli seviyeye ayarlayın. Akım probu ve ölçüm alıcısı ile akımı izleyin.
C. Mevcut seviyeyi en azından geçerli limitte belirtilen seviyede tutarken, sinyal üretecini Tablo III'e göre gerekli frekans aralığı üzerinden tarayın. EUT'yi duyarlılık açısından izleyin.
D. Duyarlılık not edilirse, 4.3.10.4.3'e göre eşik seviyesini belirleyin.
E. Test edilecek EUT'nin her yüzeyindeki her çapraz test noktası seti için 5.11.3.4b ila 5.11.3.4d'yi tekrarlayın.
Test kurulumu aşağıdaki gibi olacaktır:
A. Şekil 2 ila 5'te ve 4.3.8'de gösterildiği ve açıklandığı gibi EUT için temel test kurulumunun sürdürülmesi gerekli değildir.
B. Kalibrasyon. Özel bir kalibrasyon gerekli değildir.
C. EUT testi.
(1) Şekil CS109-2'de gösterildiği gibi, EUT'yi ve test ekipmanını (test sinyali kaynağı, test akımı ölçüm ekipmanı ve EUT'yi çalıştırmak veya performans düşüşünü ölçmek için gerekli ekipman dahil) tek bir nokta oluşturacak şekilde yapılandırın. EUT toprak terminalini kullanarak test kurulumu için topraklayın.
(a) İzolasyon transformatörlerini kullanarak tüm AC güç kaynaklarını izole edin. DC güç için izolasyon transformatörleri geçerli değildir.
(b) Tüm giriş güç kablolarının güvenlik topraklama uçlarını ayırın.
(c) Tek noktalı bir zeminin oluşturulmasını sağlamak için EUT'yi ve test ekipmanını iletken olmayan yüzeylere yerleştirin.
(2) Enjekte edilen akımlar için test noktaları aşağıdaki gibi olacaktır:
(a) Rafa monte edilmeyecek ekipman: Yalnızca montaj yüzeyi boyunca çapraz uçlarda.
(b) Rafa monte ekipman: Ekipmanın tüm yüzeylerinde çapraz uçlarda.
(c) Güverte dinlenme ekipmanı: Ekipmanın tüm yüzeyleri boyunca çapraz uçlarda.
(d) Bölmeye monte ekipman: Ekipmanın arka yüzeyi boyunca çapraz uçlarda.
(e) Kablolar (tüm montaj yöntemleri): EUT'de sonlandırılan kablo zırhı ile test kurulumu için oluşturulan tek noktalı toprak arasında. Bu gereklilik, tek nokta topraklamaları olmadıkça, kablo ekranları ve borular için de geçerli olacaktır.
(3) Sinyal üretecini ve direnci seçilen bir dizi test noktasına bağlayın. Test noktalarına bağlantı, en az 50 cm uzunluğunda test yüzeyine dik iletkenler ile yapılmalıdır.
MIL-STD-461G CS109 Testi söz konusu olduğunda Science by EUROLAB, 25 yılı aşkın endüstriyel laboratuvar tecrübesi, uzman ekibi ve son teknoloji araçları ile sizlere en iyi hizmeti sunmayı taahhüt eder.