MIL-STD-461G CS103, iletişim alıcıları, RF yükselticileri, alıcı-vericiler, radar alıcıları, akustik alıcılar ve elektronik harp alıcıları gibi ekipman ve alt sistemler için 15 kHz ila 10 GHz arasında geçerli bir alıcı ön uç duyarlılık gereksinimidir.
MIL-STD-461G CS103, EUT'nin, bireysel tedarik şartnamesinde sağlanan sınır şartına tabi tutulduğunda, belirtilen toleransların ötesinde herhangi bir intermodülasyon ürünü sergilememesini zorunlu kılar.
Bu test prosedürü, EUT anten giriş portlarında istenmeyen sinyallerden kaynaklanabilecek intermodülasyon ürünlerinin varlığını belirlemek için kullanılır.
Bu standardın ana gövdesinde bu gereklilik için herhangi bir test prosedürü sağlanmamıştır. Geliştirilmekte olan çok çeşitli alıcı tasarımları nedeniyle, anlamlı test prosedürleri geliştirilmeden önce bir alıcının belirli operasyonel özellikleri için gereksinimler oluşturulmalıdır. Bu ekte sadece genel test teknikleri tartışılmaktadır.
İntermodülasyon testi, alıcılar, RF yükselticileri, alıcı-vericiler ve aktarıcılar gibi çeşitli alıcı alt sistemlere uygulanabilir.
İntermodülasyon yanıtları için uygun test için birkaç alıcı ön uç özelliği bilinmelidir. Bu özellikler genellikle yapılan test ile belirlenmelidir. Test seviyelerinin makul olduğundan ve testin intermodülasyon etkilerini gerçekten değerlendirdiğinden emin olmak için alıcının aşırı yüklenme olmadan tolere edebileceği maksimum sinyal girişinin bilinmesi gerekir.
Alıcının bant geçiş özellikleri, alıcı temeline yakın frekansları belirlemek için önemlidir .bu testten çıkarılacaktır. Bu test için gereklilikler, genellikle, potansiyel olarak enterferans yapan sinyaller ile test edilen alıcının belirlenmiş hassasiyeti arasındaki seviye farkı belirtilerek, göreceli reddetme derecesi cinsinden ifade edilir. Bu nedenle, alıcının hassasiyetinin belirlenmesi, testin önemli bir parçasıdır.
Bu testin temel konsepti, iki bant dışı sinyali birleştirmek ve alıcıyı istenmeyen bir yanıt için izlerken bunları alıcının anten portuna uygulamaktır. Bant dışı sinyallerden biri normal olarak alıcı tarafından beklenen modülasyonla modüle edilir. İkinci sinyal normalde sürekli dalgadır (CW). Şekil A-13, bu test için genel bir kurulumu göstermektedir.
Test Kurulumu
Bir alıcı sinyali olmadan alıcının paraziti göstermediği uygulamalar için, temelde üçüncü bir sinyal kullanılabilir. Bu düzenleme, bir bant dışı sinyalde asla beklenmeyecek olan çok özel bir modülasyon tipini işleyen bazı alıcılar için de uygun olabilir. Bu uygulama için iki bant dışı sinyalin CW olması bir seçenektir.
İki bant dışı sinyalin frekansı, f o = 2f1 - f2 olacak şekilde ayarlanmalıdır, burada f oalıcının ayarlanmış frekansıdır ve f1 ve f2, sinyal kaynaklarının frekanslarıdır. Bu denklem, alıcılarda gözlenen en yaygın yanıt olan üçüncü dereceden bir intermodülasyon ürününü temsil eder. f1 ve f2, denklemdeki ilişkiyi korurken, süpürülmeli veya istenen frekans aralığının üzerine çıkmalıdır. Bu test sırasında not edilen herhangi bir yanıtın intermodülasyon yanıtlarından kaynaklandığını doğrulamak önemlidir. Yanıtlar, uygulanan sinyallerden birinin reddedilmemesinden veya sinyal kaynaklarından birinin harmoniklerinden kaynaklanabilir. Her bir sinyal kaynağını sırayla kapatmak ve yanıtın devam edip etmediğini not etmek, yanıtın kaynağını gösterebilir.
Bir anten modülünde ön uç miksajı ve filtrelemesi olan alıcılar için, testin ışınım temelinde gerçekleştirilecek şekilde tasarlanması gerekebilir. Gözlemlenen intermodülasyon ürünlerinin alıcıdan kaynaklanması ve test alanındaki öğelerden kaynaklanmaması koşuluyla, tüm sinyallerin yayılması ve garanti edilmesi gerekir. EMITP'nin anten türlerini, anten konumlarını, anten polarizasyonlarını ve alan ölçüm tekniklerini ele alması gerekir. Bu testin muhtemelen yankısız bir odada yapılması gerekecektir.
MIL-STD-461G EK A 223 Frekans atlamalı alıcılar için olası bir yaklaşım, bir f oatlama içinde yukarıda açıklandığı gibi sinyal kaynaklarını ayarlayın ve kurun. Alıcının performansı daha sonra alıcı atlama olarak değerlendirilebilir. Frekans atlamalı alıcının yalnızca bir sabit frekans kullanan bir çalışma modu varsa, bu mod da test edilmelidir. Bu test prosedürünü gerçekleştirirken yapılan yaygın bir hata, aslında test kurulumunda üretilen sinyal kaynağı veya intermodülasyon ürünlerinin harmonikleri olan arızaları EUT'ye atfetmektir. Bu nedenle, EUT anten portunda görünen sinyallerin, Şekil A-13'te gösterildiği gibi bir ölçüm alıcısı kullanılarak yalnızca amaçlanan sinyaller olduğunun doğrulanması önemlidir. Hasarlı, aşınmış ve hatalı bileşenler, yanıltıcı sonuçlara yol açan sinyal bozulmasına neden olabilir. İzleme ayrıca filtreler, zayıflatıcılar, kuplörler ve kabloların neden olduğu yol kayıplarını da belirleyecektir.
MIL-STD-461G CS103 Testi söz konusu olduğunda Science by EUROLAB, 25 yılı aşkın endüstriyel laboratuvar tecrübesi, uzman ekibi ve son teknoloji araçları ile sizlere en iyi hizmeti sunmayı taahhüt eder.